An amplifier circuit shall amplify a microphone signal in such a way that a loudspeaker ($R_{LS}= 8.0 ~\Omega$) can be driven. The rms value of the desired voltage across the loudspeaker shall be $U_{RMS,LS} = 10 ~V$. It is assumed that a sinusoidal signal is to be output. The power is supplied by two voltage sources with $V_{S+} = 15 ~V$ and $V_{S-} = - 15 ~V$. For understanding (especially for tasks 2. and 3.), look at the simulation under the subchapter equivalent circuit in chapter „1. amplifier basics“. This example shows a realistic amplifier, but also the idealized current flow can be guessed from this.

1. Draw a labelled sketch of the circuit with the amplifier as a black box.

   
   
   
   
   
   
   
   
   
   
   

2. What power $P$ does the loudspeaker consume?

   
   
   
   
   
   
   
   
   
   
   

3. From this, how can we determine the rms current $I_{RMS,S}$ of the power supply at which the above desired voltage $U_{RMS,LS}$ is output at the loudspeaker?

   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

4. Determine from the previous task the maximum current $I_{max,S}$ for which the two power supplies must be designed at least.
   (Note that for simple amplifiers the output current $I_O$ is always less than or equal to the current $I_S$ of the power supply).

   
   
   
   
   
   
   
   
   
   
   

A voltage amplifier circuit is given, which shall amplify a microphone signal in such a way that a loudspeaker ($R_{LS}= 8.0 ~\Omega$) can be driven. Neither amplification nor the desired voltage at the loudspeaker is known. This amplifier circuit is internally protected against over-currents above $I_{max,amplifier}= 5.0 ~A$ by a fast fuse. It is known that no over-currents occur in the allowed voltage operation of $8.0 ~\Omega$ loudspeakers.

1. By what factor does the current change if a $4.0 ~\Omega$ loudspeaker is used instead of an $8.0 ~\Omega$ loudspeaker?

   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

2. What effect does this have on the fuse?

   
   
   
   
   
   
   
   
   
   
   

Imagine that you work in the company „HHN Mechatronics & Robotics“. You are developing an IoT system that will be used in a harsh environment and will contain a rechargeable battery. The temperature of the battery must be monitored during operation and charging. If the temperature is too high, charging must be aborted or a warning issued. For the temperature measurement at the housing of the used lithium-ion cell NCR18650 a measuring circuit is to be built up. A suggestion for the circuit is as follows:

1. Wheatstone bridge circuit with $R_1 = R_2 = R_3 = R_4 = 1.0k \Omega $.
2. Let the resistor $R_4$ be a PT1000 with a temperature coefficient $\alpha = 3850 \frac{ppm}{K}$.
3. For the other resistors, to components are chosen, that have an unknown temperature coefficient. According to the data sheet temperature coefficient is within $\alpha = \pm 100 \frac{ppm}{K}$.
4. The voltage source of the system generates a voltage of 5V with sufficient accuracy.
5. The determined voltage $\Delta U$ is amplified by a factor of 20 through another amplifier circuit, output as $U_{O}$, and further used by an analog-to-digital converter in a microcontroller ¹⁾.

A short report is to be created; Tina TI is to be used as the analysis tool.

1. Create a problem description.

   
   
   
   
   
   
   
   
   
   
   
2. Rebuild the circuit in TINA TI and add this in your descriptionhere. Take the following hint into account.

   Hint

   Use a simple resistor for the PT1000 in the simulation. With Tina TI, 27°C (room temperature) is selected as the reference temperature for the temperature curve. For the PT1000, the reference temperature is often 0°C (in practical applications, this should be checked in the data sheet). With Tina TI, the reference temperature can be changed by entering the value 27 under Temperature [C] in the properties (double-click on Resistor).

   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

3. From the data sheet linked above, determine in what range from $T_{min}$ to $T_{max}$ may be charged and what temperature $T_{lim}$ may not be exceeded in any of the states.

   
   
   
   
   
   
   
   
   
   
   
   
   
   

4. First, for temperature invariant $R_1 = R_2 = R_3 = 1.0k \Omega$ and a temperature variable resistor $R_4$, determine the voltage change $\Delta U$ over the temperature of $-30...70°C$ in TINA TI. To do this, create a plot with $\Delta U$ as a function of temperature.
   Read $\Delta U^0 (T_{min})$, $\Delta U^0 (T_{max})$, $\Delta U^0 (T_{lim})$, from the diagram and check the plausibility of the values by calculation.

   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

5. Determine $\Delta U$ when the temperature dependence of $R_1$, $R_2$ and $R_3$ is taken into account. To do this, create a suitable diagram with $\Delta U$ as a function of temperature in TINA TI.
   At what voltages $U_O (T_{min})$, $U_O (T_{max})$ must the microcontroller intervene and disable charging?
   At what value $U_A (T_{lim})$ must a warning be issued?

   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   
   

6. Discuss the results