Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
lab05_en:inverting_op-amp_photo_diode_as_current_source [2026/04/20 11:09] – mexleadminlab05_en:inverting_op-amp_photo_diode_as_current_source [2026/04/28 16:13] (current) – mexleadmin
Line 1: Line 1:
-=== Photo Diode as current source ===+=== Photodiode as current source ===
 \\ \\
 \\ \\
Line 5: Line 5:
 {{drawio>lab05:Fig-120_inverting_op-amp_photo_diode_housing.svg}}\\ {{drawio>lab05:Fig-120_inverting_op-amp_photo_diode_housing.svg}}\\
 \\ \\
-<imgcaption Fig-120_inverting_op-amp_photo_diode_housing | Inverting Op-Amp: Photo Diode BPW 34 S> </imgcaption>\\+<imgcaption Fig-120_inverting_op-amp_photo_diode_housing | Inverting Op-Amp: Photodiode BPW 34 S> </imgcaption>\\
 \\ \\
 \\ \\
Line 11: Line 11:
 \\ \\
 <imgcaption Fig-110_inverting_op-amp_photo_diode_diagramms | Inverting Op-Amp: Diagramms of BPW 34 S> </imgcaption>\\ <imgcaption Fig-110_inverting_op-amp_photo_diode_diagramms | Inverting Op-Amp: Diagramms of BPW 34 S> </imgcaption>\\
 +\\
 +\\
 +\\
 +\\
 \\ \\
 \\ \\
Line 20: Line 24:
 \\ \\
 \\ \\
-We assume a good illuminated room of 300 lx, illuminated by a white LED. White light is a mixture of many wavelengths across the visible spectrum, roughly 380 to 780 nm.\\ +We are assuming a well-lit room with an illuminance of 300 lx, lit by a white LED. White light is a mixture of many wavelengths across the visible spectrum, roughly 380 to 780 nm. For a typical white LED, the spectrum usually comes from a blue LED chip with a peak around 450 nm, plus a broader phosphor emission that spreads across green, yellow, and red wavelengths. For an easier calculation, we take a mean value of 500 nm which is close to the peak value of the blue LED and 300 lx for the illumination. (500 nm is in reality a greenish light and not blue)\\ 
-For a typical white LED, the spectrum usually comes from a blue LED chip with a peak around 450 nm, plus a broader phosphor emission that spreads across green, yellow, and red wavelengths.\\ +The graph in <imgref Fig-110_inverting_op-amp_photo_diode_diagramms> shows that the photodiode sensitivity at 500 nm is only 30%. The maximim current (100%) at 300 lx is 30 ${\rm\mu}$A.\\ 
-For an easier calculation, we take a mean value of 500 nm which is close to the peak value of the blue LED (in reality a greenish light) and 300 lx for the illumination.\\ +We can now estimate the current we would expect from the photodiode at 300 lx:\\
-In the diagram in <imgref Fig-110_inverting_op-amp_photo_diode_diagramms> we see that the sensitivity of the photo diode at 500 nm ist only 30%. The maximim current (100%) at 300 lx is 30 ${\rm\mu}$A.\\ +
-Now we can calculate the current we expect from the diode at 300 lx:\\+
 \\ \\
-$I_{\rm 1} = 30 {\rm~\mu A} * 0.3$\\+$I_{\rm 1} = 30 {\rm~\mu A} * 0.3 = 9 {\rm~\mu A}$\\
 $I_{\rm 1} \approx 10 {\rm~\mu A}$\\ $I_{\rm 1} \approx 10 {\rm~\mu A}$\\
 \\ \\
 30% of 30 ${\rm\mu A}$ is roughly 10 ${\rm\mu A}$.\\ 30% of 30 ${\rm\mu A}$ is roughly 10 ${\rm\mu A}$.\\
 +**We will assume a current of 10 ${\rm\mu A}$ at 300 lx for our calculations.**\\
 \\ \\
 +Complete the arrows in the circuit diagram in <imgref Fig-100_inverting_op-amp_photo_diode>.\\
 \\ \\
-Complete the arrows in the scematic of the circuit.\\ +Calculate $R_{\rm 2}$ so that $U_{\rm OUT}$ = 5 V at 300 lx.  
-Calculate ${\rm R_2}$ so that $U_{\rm OUT}$ = 5 V at 300 lx.  +Take a resistor from the E6 series that is as close as possible to the calculated value.\\ 
-Take a resistor from the E6 series that is as close as possible to the calculated value.+Also enter the values for $I_{\rm 1}$, $I_{\rm 2}$, $U_{\rm 2}$ and $U_{\rm OUT}$.\\
 \\ \\
 \\ \\
-$I_{\rm D}{\rm~=}$\\ 
 \\ \\
 \\ \\
-$I_{\rm 2}{\rm~=}$\\+$I_{\rm 1}{\rm~=}$\\
 \\ \\
 \\ \\
-$U_{\rm OUT}{\rm~=}$\\+$I_{\rm 2}{\rm~=}$\\
 \\ \\
 \\ \\
 $U_{\rm 2}{\rm~=}$\\ $U_{\rm 2}{\rm~=}$\\
 +\\
 +\\
 +$U_{\rm OUT}{\rm~=}$\\
 \\ \\
 \\ \\
Line 71: Line 77:
 \\ \\
 \\ \\
-What value would you expect for $U_{\rm D}$ and why?\\+What value would you expect for $U_{\rm D}$ in <imgref Fig-100_inverting_op-amp_photo_diode> and why?\\
 \\ \\
 \\ \\
Line 91: Line 97:
 \\ \\
 \\ \\
-What value would you expect for $U_{\rm D}$ when it is not connected to the Op-Amp or any other electronic component (open-circuit voltage) at 300 lx?\\+What value would you expect for $U_{\rm D}$ at 300 lx when the photodiode is not connected to the Op-Amp or any other electronic component (open-circuit voltage) and why?\\
 \\ \\
 \\ \\
Line 106: Line 112:
 \\ \\
 ${\rm ................................................................................................}$\\ ${\rm ................................................................................................}$\\
 +\\
 +${\rm ................................................................................................}$\\
 +\\
 +\\
 +\\
 +\\
 +Measure or calculate the values given in the table below.
 +\\
 +\\
 +{{drawio>lab05:Table-1_inverting_op-amp_photo_diode.svg}}\\
 +<tabcaption lab05:Table-1_inverting_op-amp_photo_diode | Photodiode measured and calculated values> </tabcaption>\\
 +\\
 +\\
 +\\
 +\\
 +\\
 +\\
 +\\
 +\\
 +\\
 +\\
 \\ \\
 \\ \\